hacker

turmio

Boot messages

U-boot DB120


DRAM:  128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

PCIe Reset OK!!!!!!
In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
 wasp  reset mask:c03300 
WASP  ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Booting Atheros AR934x
[    0.000000] Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Mon Jun 17 12:35:36 CST 2013
[    0.000000] Ram size passed from bootloader =128M
[    0.000000] flash_size passed from bootloader = 8
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00008000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00008000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(ART) mem=128M
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 112924k/131072k available (1852k kernel code, 17984k reserved, 428k data, 120k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] plat_time_init: plat time init done
[    0.000000] Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
[    0.096000] Mount-cache hash table entries: 512
[    0.096000] 
[    0.096000] ****************ALLOC***********************
[    0.096000]  Packet mem: 8026c4c0 (0xe00000 bytes)
[    0.096000] ********************************************
[    0.096000] 
[    0.096000] NET: Registered protocol family 16
[    0.096000] PCI init:ath_pcibios_init
[    0.096000] ath_pcibios_init(294): PCI CMD write: 0x356
[    0.096000] registering PCI controller with io_map_base unset
[    0.096000] bio: create slab <bio-0> at 0
[    0.096000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.096000] pci 0000:00:00.0: PME# disabled
[    0.096000] Returning IRQ 64
[    0.100000] NET: Registered protocol family 2
[    0.100000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.100000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.100000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.100000] TCP reno registered
[    0.100000] NET: Registered protocol family 1
[    0.100000] ATH GPIOC major 0
[    0.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.100000] msgmni has been set to 220
[    0.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.100000] io scheduler noop registered
[    0.100000] io scheduler deadline registered (default)
[    0.100000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.104000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[    0.104000] console [ttyS0] enabled
[    0.404000] PPP generic driver version 2.4.2
[    0.408000] NET: Registered protocol family 24
[    0.412000] 5 cmdlinepart partitions found on MTD device ath-nor0
[    0.420000] Creating 5 MTD partitions on "ath-nor0":
[    0.424000] 0x000000000000-0x000000020000 : "u-boot"
[    0.428000] 0x000000020000-0x000000120000 : "kernel"
[    0.436000] 0x000000120000-0x0000007e0000 : "rootfs"
[    0.440000] 0x0000007e0000-0x0000007f0000 : "config"
[    0.444000] 0x0000007f0000-0x000000800000 : "ART"
[    0.452000] ->Oops: flash id 0xef4017 . 
[    0.456000] ----TP IGMP has been init------
[    0.460000] TCP cubic registered
[    0.460000] NET: Registered protocol family 10
[    0.468000] NET: Registered protocol family 17
[    0.472000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    0.480000] All bugs added by David S. Miller <davem@redhat.com>
[    0.484000] athwdt_init: Registering WDT success
[    0.488000] ath_otp_init: Registering OTP success
[    0.496000] ath_clksw_init: Registering Clock Switch Interface success
[    0.508000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.516000] Freeing unused kernel memory: 120k freed
init started:  BusyBox v1.01 (2013.05.24-01:06+0000) multi-call binary
This Board use 2.6.31
insmod: cannot open module `/lib/modules/2.6.31/kernel/x_tables.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xt_tcpudp.ko': No such file or directory
[    1.660000] xt_time: kernel timezone is -0000
[    1.860000] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    1.864000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    1.872000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    1.880000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    2.272000] ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
[    2.652000] PPPoL2TP kernel driver, V1.0
[    2.676000] PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory

 (none) mips #1 Mon Jun 17 12:35:36 CST 2013 (none)
(none) login: [    6.064000] Now flash open!
[    6.700000] Now flash open!
[    7.048000] ATHR_GMAC: Length per segment 1536
[    7.052000] ATHR_GMAC: fifo cfg 3 01f00140
[    7.056000] ATHR_GMAC: RX TASKLET - Pkts per Intr:100
[    7.060000] ATHR_GMAC: Mac address for unit 0:bfff0000
[    7.068000] ATHR_GMAC: ff:ff:ff:ff:ff:ff 
[    7.620000] ATHR_GMAC: Max segments per packet :   1
[    7.628000] ATHR_GMAC: Max tx descriptor count :   128
[    7.632000] ATHR_GMAC: Max rx descriptor count :   128
[    7.636000] ATHR_GMAC: Mac capability flags    :   2381
[    7.652000] athr_gmac_ring_alloc Allocated 2048 at 0x87af2000
[    7.656000] athr_gmac_ring_alloc Allocated 2048 at 0x87a5b800
[    7.964000] WASP  ----> S17 PHY *
[    7.968000] Setting Drop CRC Errors, Pause Frames and Length Error frames 
[    8.040000] Hello, nat module!
[    8.044000] thread: napt_ct_scan create success pid:108
[    8.048000] netlink_kernel_create succeeded at tp_rule_nl_prot: [29]
[    8.056000] isis_ip_intf_entry_add id[0] for vid[1]
[    8.064000] isis_ip_intf_entry_add id[1] for vid[2]
[    8.068000] ACL(Index 0) For packet From Wan Port and TTL is zero
[    8.080000] ACL is not yet enabled. Enabling... 
[    8.088000] ACL Rule(Index 2) For UDP with Zero Checksum
[    8.104000] 
[    8.104000] ######## S17 SSDK init succeeded! ########
[    8.120000] ++++ athrs17_igmp_setup once
[    8.148000] athrs17_reg_init:done
[    8.152000] Setting PHY...
[    9.160000] napt_ct_scan_thread: time: 4
[    9.164000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[    9.228000] device eth0.1 entered promiscuous mode
[    9.232000] device eth0 entered promiscuous mode
[    9.248000] Now flash open!
[    9.252000] Receive unknown msgType:10 at isis_nat_helper.2631.c:2937/tp_rule_netlink()!
[    9.260000] isis_ip_intf_entry_add id[1] for vid[2]
[    9.348000] br0: port 1(eth0.1) entering forwarding state
[   11.008000] ACL Rule(Index 1) For Packet From WAN to LAN Port And DIP is in lan net
[   11.500000] nf_conntrack_rtsp v0.6.21 loading
[   11.516000] nf_nat_rtsp v0.6.21 loading
[   11.660000] 
[   11.660000] Enet:0 port1 up
[   11.664000] ATH_MAC_TIMER: enet unit:0 is up...
[   11.668000] RGMii 1000Mbps full duplex
[   11.672000] ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl  
[   11.680000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   11.828000] asf: module license 'Proprietary' taints kernel.
[   11.832000] Disabling lock debugging due to kernel taint
[   12.400000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
[   12.528000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[   12.560000] ath_dfs: Version 2.0.0
[   12.560000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[   12.904000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[   13.676000] ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
[   13.684000] __ath_attach: Set global_scn[0]
[   13.688000] ACBKMinfree = 48
[   13.692000] ACBEMinfree = 32
[   13.696000] ACVIMinfree = 16
[   13.696000] ACVOMinfree = 0
[   13.700000] CABMinfree = 48
[   13.704000] UAPSDMinfree = 0
[   13.732000] Restoring Cal data from Flash
[   13.740000] dfs_attach: use DFS enhancements
[   13.748000] DFS min filter rssiThresh = 18
[   13.752000] DFS max pulse dur = 151 ticks
[   13.760000] ath_get_caps[5108] rx chainmask mismatch actual 3 sc_chainmak 0
[   13.764000] ath_get_caps[5083] tx chainmask mismatch actual 3 sc_chainmak 0
[   13.780000] SC Callback Registration for wifi0
[   13.784000] wifi0: Atheros 9340: mem=0xb8100000, irq=2
[   13.792000] ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
[   13.796000] __ath_attach: Set global_scn[1]
[   13.800000] ACBKMinfree = 48
[   13.804000] ACBEMinfree = 32
[   13.804000] ACVIMinfree = 16
[   13.808000] ACVOMinfree = 0
[   13.812000] CABMinfree = 48
[   13.816000] UAPSDMinfree = 0
[   13.824000] Restoring Cal data from Flash
[   13.832000] dfs_attach: use DFS enhancements
[   13.840000] DFS min filter rssiThresh = 18
[   13.844000] DFS max pulse dur = 151 ticks
[   13.848000] ath_get_caps[5108] rx chainmask mismatch actual 7 sc_chainmak 0
[   13.852000] ath_get_caps[5083] tx chainmask mismatch actual 7 sc_chainmak 0
[   13.868000] SC Callback Registration for wifi1
[   13.876000] wifi1: Atheros 9580: mem=0x10000000, irq=64 hw_base=0xb0000000
[   14.100000] wlan_vap_create : enter. devhandle=0x86c3c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
[   14.108000] wlan_vap_create : exit. devhandle=0x86c3c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[   14.116000] VAP device ath0 created 
[   14.272000]  
[   14.272000]  DES SSID SET=TP-LINK_2.4GHz_3B4D8D 
[   14.288000]  ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 
[   20.252000] device ath0 entered promiscuous mode
[   20.256000] br0: port 2(ath0) entering forwarding state
[   20.860000]  ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1 
[   20.876000] br0: port 2(ath0) entering disabled state
[   21.084000]  
[   21.084000]  DES SSID SET=TP-LINK_2.4GHz_3B4D8D 
[   21.112000] br0: port 2(ath0) entering forwarding state
[   22.984000] br0: port 2(ath0) entering disabled state
[   23.016000] br0: starting userspace STP failed, starting kernel STP
[   23.052000] br0: topology change detected, propagating
[   23.060000] br0: port 2(ath0) entering forwarding state
[   23.108000] wlan_vap_create : enter. devhandle=0x87bac2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
[   23.116000] wlan_vap_create : exit. devhandle=0x87bac2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[   23.124000] VAP device ath1 created 
[   23.284000]  
[   23.284000]  DES SSID SET=TP-LINK_5GHz_3B4D8E 
[   23.300000]  ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 
[   27.704000] Found best 11na chan: 36
[   29.176000] br0: port 1(eth0.1) entering disabled state
[   29.200000] br0: topology change detected, propagating
[   29.204000] br0: port 1(eth0.1) entering forwarding state
[   29.228000] device ath1 entered promiscuous mode
[   29.232000] br0: topology change detected, propagating
[   29.240000] br0: port 3(ath1) entering forwarding state
[   29.276000]  ieee80211_ioctl_siwmode: imr.ifm_active=852608, new mode=3, valid=1 
[   29.284000] br0: port 3(ath1) entering disabled state
[   29.492000]  
[   29.492000]  DES SSID SET=TP-LINK_5GHz_3B4D8E 
[   29.516000] br0: topology change detected, propagating
[   29.524000] br0: port 3(ath1) entering forwarding state
[   31.296000] br0: port 3(ath1) entering disabled state
[   31.356000] br0: topology change detected, propagating
[   31.360000] br0: port 3(ath1) entering forwarding state
[   31.800000] fuse init (API version 7.12)
[   32.004000] usbcore: registered new interface driver usbfs
[   32.008000] usbcore: registered new interface driver hub
[   32.016000] usbcore: registered new device driver usb
[   32.048000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   32.096000] Port Status 1c000004 
[   32.096000] ath-ehci ath-ehci.0: ATH EHCI
[   32.100000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
[   32.112000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[   32.116000] ehci_reset Port Status 1c000000 
[   32.120000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
[   32.128000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[   32.136000] ehci_reset Port Status 1c000000 
[   32.152000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
[   32.156000] usb usb1: configuration #1 chosen from 1 choice
[   32.164000] hub 1-0:1.0: USB hub found
[   32.168000] hub 1-0:1.0: 1 port detected
[   32.388000] SCSI subsystem initialized
[   32.508000] usb 1-1: new high speed USB device using ath-ehci and address 2
[   32.652000] usb 1-1: configuration #1 chosen from 1 choice
[   32.660000] hub 1-1:1.0: USB hub found
[   32.664000] hub 1-1:1.0: 4 ports detected
[   32.724000] Initializing USB Mass Storage driver...
[   32.728000] usbcore: registered new interface driver usb-storage
[   32.736000] USB Mass Storage support registered.
[   32.956000] usb 1-1.2: new high speed USB device using ath-ehci and address 3
[   33.068000] usb 1-1.2: configuration #1 chosen from 1 choice
[   33.084000] scsi0 : SCSI emulation for USB Mass Storage devices
[   34.412000]  GPL NetUSB up!
[   34.640000] kc   88 : run_telnetDBGDServer start 
[   34.644000] kc  225 : init_DebugD end
[   34.648000] INFO16B9: NetUSB 1.161, 0002061F : Feb 29 2012 15:22:09
[   34.656000] INFO16BB:  AUTH ISOC
[   34.660000] INFO16BC: 
[   34.660000] usbcore: registered new interface driver KC NetUSB General Driver
[   34.668000] INFO0076:  init proc : PAGE_SIZE 4096
[   34.676000] INFO1715: Check mac address
[   34.680000] INFO1575:  sleep to wait br0 to wake up
[   34.684000] INFO02D0:  use dev Name br0 
[   34.688000] INFO157E:  sleep to wait br0 end.
[   34.692000] INFO1597:  UDP_BROAD 7437 tcpPort:625868800 
[   34.696000] INFO02D0:  use dev Name br0 
[   34.700000] my server name : TL-WDR4300
[   34.708000] INFO14CE: tcpConnector() started...
[   34.720000] TP_RULE_NAT:enable hardware nat
[   34.852000] IPv6 over IPv4 tunneling driver
[   37.216000] (tp_mroute_enable_write)140, tp_mroute_enable = 1
[   37.732000] INFO13AB: Bind to br0
[   38.292000] scsi 0:0:0:0: Direct-Access     USB      Flash Disk       1100 PQ: 0 ANSI: 4
[   38.300000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   38.308000] sd 0:0:0:0: [sda] 3915776 512-byte logical blocks: (2.00 GB/1.86 GiB)
[   38.316000] sd 0:0:0:0: [sda] Write Protect is off
[   38.320000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   38.332000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   38.336000]  sda: sda1
[   38.348000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   38.352000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   38.376000] SQUASHFS error: Can't find a SQUASHFS superblock on sda
[   38.384000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[   38.392000] FAT: bogus number of reserved sectors
[   38.400000] VFS: Can't find a valid FAT filesystem on dev sda.
[   38.900000] SQUASHFS error: Can't find a SQUASHFS superblock on sda1
[   38.908000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[   41.404000] Now flash open!
[   41.408000] Erase from 0X7E0000 to 0X7EFCB4:.
[   41.632000] Program from 0X7E0000 to 0X7EFCB4:
[   41.800000] write successfully
[   41.808000] Now flash open!
[   41.808000] Erase from 0X7E0000 to 0X7EFCB4:
[   42.032000] .
[   42.036000] Program from 0X7E0000 to 0X7EFCB4:
[   42.204000] write successfully
description
Reverse engineering
started
2014-03-20


CategoryProjekti