{{{ ?CU-Boot 1.1.4-g5da25403 (Jul 22 2015 - 04:09:32) bsb002 - Honey Bee 2.0DRAM: sri Honey Bee 2.0 ath_ddr_initial_config(195): (16bit) ddr2 init tap = 0x00000003 Tap (low, high) = (0x8, 0x20) Tap values = (0x14, 0x14, 0x14, 0x14) 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 214k for U-Boot at: 83fc8000 Reserving 192k for malloc() at: 83f98000 Reserving 44 Bytes for Board Info at: 8d4 Reserving 36 Bytes for Global Data at: 83f97fb0 Reserving 128k for boot params() at: 83f77fb0 Stacnter at: 83f77f98 Now running in RAM - U-Boot at: 83fc8000 Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x13 flash size 0MB, sector count = 8 Flash: 512 kB *** Warning *** : PCIe WLAN Module not found !!! In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... Fetching MAC Address from 0x83febe80 Fetching MAC Address from 0x83febe80 ath_gmac_enet_initialize: reset mask:c02200 Scorpion ---->S27 PHY* S27 reg init : cfg1 0x800c0000 cfg2 0x7114 eth0: 00:03:7f:11:20:ce athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10 eth0 up Honey Bee ----> MAC 1 S27 PHY * S27 reg init ATHRS27: resetting s27 ATHRS27: s27 reset done : cfg1 0x800c0000 cfg2 0x7214 eth1: 00:17:88:21:79:c6 athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10 athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000 athrs27_phy_seATHR_PHY_SPEC_STAUS 1 :10 athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000 athrs27_phy_ ATHR_PHY_SPEC_STAUS 2 :10 athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000 athrs27_phy_setup ATHR_PHY_SPEC_S3 :10 eth1 up eth0, eth1 Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc. ====== NAND Parameters ====== sc = 0x83ff6ab0 page = 0x800 block = 0x20000Setting 0162c0 to 0x3061a100 Hit any key to stop autoboot: 0 Loading from device 0: ath-spi-nand (offset 0x0) Image Name: MIPS OpenWrt Linux-3.14 Created: 2015-07-22 10:29:19 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1218297 B= 1.2 MB Load Address: 80060000 Entry Point: 80060000 ## Booting image at 81000000 ... Image Name: MIPS OpenWrt Linux-3.14 Created: 2015-07-22 10:29:19 UTC Image Type: MIPS Linux Kernel Image (lzma compr) Data Size: 1218297 Bytes = 1.2 MB Load Address: 80060000 Entry Point: 80060000 Veng Checksum at 0x81000040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 3.14.0 (huebridge@huebridgelinuxbuild) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40838) ) #4 Wed Jul 22 12:29:09 CEST 2015 [ 0.0] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoClcomm Atheros QCA9533 rev 2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000003ffffff] [ 0.000000] Movable start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1 [ 0.000000] Kernel command line: ubi.mtd=5 board=BSB002 console=ttyS0,115200 ubi.mtd=overlay rootev/mtdblock:rootfs rootfstype=squashfs noinitrd init=/sbin/init mtdparts=spi0.0:256k(u-boot)ro,128k(u-env),64k(reserved),64k(art);spi0.1:4m(kernel-0)ro,40m(root-0),4m(kernel-1),40m(root-1),-(overlay) mem=ootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 819der: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=0000 [ 0.000000] Memory: 60756K/65536K available (2712K kernel code, 126K rwdata, 576K rodata, 160K init, 185K bss, 4780K reserved) [ 0.000000] SLUB: HWalign=32, Order=0inObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:650.000MHz, DDR:597.583MHz, AHB:216.666MHz, Ref:25.000MHz [.000000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] Mountpoint-cachsh table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] NET: Registered protocol family 16 [ 0.080000] MIPS: machine is Philips BSB002 board [ 0.090000] ar71xx: invalid MDIO id 1 [ 0.500000] bio: create slab at 0 [ 0.510000] Switched to clocksource MIPS [ 0.510000] NET: Registered protocol family 2 [ 0.520000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.520000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.530000] Hash tables configured (established 1024 bind 1024) [ 0.540000] TCP: reno registered [ 0.540000] UDP table entries: 256 (order: 0, 4096 bytes) [ 0.540000] UDP-Lite hash table entries: 256 (order: 0, bytes) [ 0.550000] NET: Registered protocol family 1 [ 0.560000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.580000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.590000] msgmni has been set to 118 [ 0.600000] io scheduler noop registered [ 0.600000] io scheduler deadline registered (default) [ 0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A [ 0.640000] console [ttyS0] enabled [ 0.640000] console [ttyS0] enabled [ 0.650000] bootconsole [early0] disabled [ 0.650000] bootconsole [early0] disabled [ 0.660000] m25p80 spi0.0: found gd25d40, expected m25p80 [ 0.670000] m25p80 spi0.0: gd25d40 (512 Kbytes) [ 0.670000] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.680000] Creating 4 MTD partitions on "spi0.0": [ 0.680000] 0x000000000000-0x000000040000 : "u-boot" [ 0.690000] 0x000000040000-0x000000060000 : "u-boot-env" [ 0.690000] 0x000000060000-0x000000070000 : "reserved" [ 0.700000] 0x000000070000-0x000000080000 : "art" [ 0.710000] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xb1 [ 0.720000] nand: Giga Device GD5F1GQ4U 1G 3.3V 8-bit [ 0.720000] nand: 128MiB, SLC, page size: 2048, OOB size: 128 [ 0.730000] Scanning device for bad blocks [ 0.860000] Bad eraseblock 580 at 0x000004880000 [ 0.900000] Bad eraseblock 768 at 0x000006000000 [ 0.960000] Bad eraseblock 1023 at 0x000007fe0000 [ 0.970000] 5 cmdlinepart partitions found on MTD device spi0.1 [ 0.970000] Creating 5 MTD partitions on "spi0.1": [ 0.980000] 0x000000000000-0x000000400000 : "kernel-0" [ 0.980000] 0x000000400000-0x000002c00000 : "root-0" [ 0.990000] 0x000002c00000-0x000003000000 : "kernel-1" [ 1.000000] 0x000003000000-0x000005800000 : "root-1" [ 1.000000] 0x000005800000-0x000008000000 : "overlay" [ 1.030000] libphy: ag71xx_mdio: probed [ 1.670000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 1.680000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 2.240000] ag71xx-mdio.1: Found an AR934X built-in switch [ 3.270000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 3.270000] i2c /dev entries driver [ 3.280000] TCP: cubic registered [ 3.280000] NET: Registered protocol family 17 [ 3.290000] 8021q: 802.1Q VLAN Support v1.8 [ 3.290000] UBI: attaching mtd5 to ubi0 [ 4.690000] UBI: scanning is finished [ 4.740000] UBI: attached mtd5 (name "root-0", size 40 MiB) to ubi0 [ 4.750000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.760000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.760000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.770000] UBI: good PEBs: 320, bad PEBs: 0, corrupted PEBs: 0 [ 4.780000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.780000] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 929738493 [ 4.790000] UBI: available PEBs: 265, total reserved PEBs: 55, PEBs reserved for bad PEB handling: 20 [ 4.800000] UBI: background thread "ubi_bgt0d" started, PID 273 [ 4.810000] mtd: device 9 (rootfs) set to be root filesystem [ 4.820000] UBI: attaching mtd8 to ubi1 [ 6.200000] UBI: scanning is finished [ 6.250000] UBI: attached mtd8 (name "overlay", size 40 MiB) to ubi1 [ 6.260000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 6.270000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 6.270000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 6.280000] UBI: good PEBs: 318, bad PEBs: 2, corrupted PEBs: 0 [ 6.290000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 6.290000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 1852693272 [ 6.300000] UBI: available PEBs: 0, total reserved PEBs: 318, PEBs reserved for bad PEB handling: 18 [ 6.310000] UBI: background thread "ubi_bgt1d" started, PID 284 [ 6.330000] VFS: Mounted root (squashfs filesystem) readonly on device 31:9. [ 6.340000] Freeing unused kernel memory: 160K (803b8000 - 803e0000) procd: Console is alive procd: - watchdog - procd: - preinit - [ 9.320000] random: mktemp urandom read with 66 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.180000] usbcore: registered new interface driver usbfs [ 10.190000] usbcore: registered new interface driver hub [ 10.190000] usbcore: registered new device driver usb [ 10.200000] Button Hotplug driver version 0.4.1 [ 10.210000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.220000] ehci-platform: EHCI generic platform driver [ 10.230000] ehci-platform ehci-platform: EHCI Host Controller [ 10.230000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 10.240000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 10.270000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 10.270000] hub 1-0:1.0: USB hub found [ 10.280000] hub 1-0:1.0: 1 port detected [ 10.600000] usb 1-1: new full-speed USB device number 2 using ehci-platform jffs2 is ready[ 11.570000] jffs2: write-buffering enabled buffer (2048) erasesize (126976) [ 11.600000] jffs2: jffs2_scan_dirent_node(): Node CRC failed on node at 0x00d347f4: Read 0xffffffff, calculated 0x74ee54b9 [ 11.930000] jffs2: notice: (350) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 12 of xref (0 dead, 7 orphan) found. switching to jffs2 procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 13.400000] NET: Registered protocol family 10 [ 13.410000] nf_conntrack version 0.5.0 (951 buckets, 3804 max) [ 13.420000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 13.460000] i2c-gpio i2c-gpio.0: using pins 12 (SDA) and 16 (SCL) [ 13.480000] Loading modules backported from Linux version v3.2-rc1-229534-gb3e71d7 [ 13.490000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 13.500000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 13.550000] usbcore: registered new interface driver usbserial [ 13.550000] usbcore: registered new interface driver usbserial_generic [ 13.570000] usbserial: USB Serial support registered for generic [ 13.610000] xt_time: kernel timezone is -0000 [ 13.690000] cfg80211: Calling CRDA to update world regulatory domain [ 13.710000] cfg80211: World regulatory domain updated: [ 13.710000] cfg80211: DFS Master region: unset [ 13.720000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 13.730000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 13.730000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 13.740000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 13.750000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 13.760000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 13.770000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 13.780000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 13.790000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 13.810000] usbcore: registered new interface driver pl2303 [ 13.820000] usbserial: USB Serial support registered for pl2303 [ 13.830000] pl2303 1-1:1.0: pl2303 converter detected [ 13.860000] usb 1-1: pl2303 converter now attached to ttyUSB0 [ 13.860000] PPP generic driver version 2.4.2 [ 13.880000] NET: Registered protocol family 24 [ 13.970000] cfg80211: Calling CRDA for country: US [ 13.980000] cfg80211: Regulatory domain changed to country: US [ 13.980000] cfg80211: DFS Master region: FCC [ 13.990000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 14.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 14.000000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A) [ 14.010000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2400 mBm), (0 s) [ 14.020000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2400 mBm), (0 s) [ 14.030000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 14.040000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 14.050000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47 [ 20.030000] random: nonblocking pool is initialized [ 24.890000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 24.930000] device eth1 entered promiscuous mode [ 24.930000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 25.550000] eth1: link up (1000Mbps/Full duplex) [ 25.550000] br-lan: port 1(eth1) entered forwarding state [ 25.560000] br-lan: port 1(eth1) entered forwarding state [ 25.560000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 25.580000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready procd: - init complete - [ 27.560000] br-lan: port 1(eth1) entered forwarding state }}} <>